Powers 410 Series Pressure Balacing Mixing Valves Bedienungsanleitung PDF herunterladen

INSTALLATION

Installation should be in accordance with accepted plumb-

ing practices. Flush all piping thoroughly before installation.

1. Position mixer 2

⁄2″ (64mm) from inlet center to finished

wall surface. Facing front of mixer, connect hot water to

left side (labeled “HOT”) and connect cold water to right

side (labeled “COLD”).

2. When copper tubing is used, flare fittings are recom-

mended. If flared fitting cannot be used, then the bal-

ancing chamber cartridge must be removed before

soldering near the Hydroguard body. Inlet checkstops

with direct sweat straight or 90° angle or straight with

⁄2″ NPT connections are available. To remove the bal-

ancing chamber cartridge, remove the four bonnet

screws and lift off the bonnet. Pull cartridge out with

either pliers or cartridge puller #401-202. Before replac-

ing the cartridge, lubricate the side O-rings with a small

amount of grease or soap.

3. Three port bodies can be

top or bottom outlet. Unit is fac-

tory-assembled for top outlet installation. See Figure 1.

For shower unit, pipe top outlet directly to showerhead.

If bottom outlet (or reversed outlets) is required, place

mixer stem in closed position (full clockwise) and

remove O-ring and Stop C (Figure 5). Rotate stem 180°

and replace stop in its initial position.

With mixer in closed position, the notch in

top spline on

the stem (Figure 3) must face the outlet for

standard

inlets (cold water to cold port). For reversed inlets (cold

water to hot port), the notch must face way from the

outlet port.

Hot and cold inlets should also be identified to avoid

confusion during fixture maintenance.

4. A 4-port valve has a double outlet body. See Figure 2.

The top outlet “S” is piped to the showerhead. The bot-

tom outlet “Tub” is piped directly to a diverter type spout.

There is a built-in diverter fitting in the Hydroguard so it is

not necessary to use a twin ell. Be sure that “Tub” is

piped to the tub. If the outlet connections are crossed,

the Hydroguard will not function properly.

5. Slide roughing-in guide onto mixer stem until it contacts

temperature stop on stem. Facing front of mixer, the

words, “Front Finished Wall Guide” can be read. Position

mixer so finished wall surface will be within

⁄4″ (19mm)

rim on the guide. This ensures the center line of the

mixer connections will be 2

⁄2″ (64mm) from the finished

wall surface. After wall is finished, remove rough-in

guide. Before assembling dial to mixer body, attach gas-

ket to inside dial and sides. Allow approximately

⁄8″

(3.2mm) of gasket to protrude past dial edge. Attach dial

to mixer body with two screws furnished. Place dial

insert inside dial. Secure with retainer (rubber). Cover

stem with sleeve, fasten lever handle to stem with screw

provided. For lucite handle, use plug button provided.

Figure 4 shows typical relationship of parts.

INSTALLATION INSTRUCTIONS

Hydroguard Pressure Balancing Valves

Series 410

Figure 2.

Rough-in dimensions

inches (millimeters)

Figure 1.

Rough-in dimensions

inches (millimeters)

Form II410

1 2

INSTALLATION INSTRUCTIONS 1

Inhaltsverzeichnis

Seite 1 - INSTALLATION INSTRUCTIONS

INSTALLATIONInstallation should be in accordance with accepted plumb-ing practices. Flush all piping thoroughly before installation. 1. Position mixer

Seite 2

MAXIMUM TEMPERATURE SETTING6. (Refer to Figure 5.) This must be set on the job. Mixerwill pass full HOT water. Loosen screw B (do notremove). Rotate s

Kommentare zu diesen Handbüchern

Keine Kommentare

Powers 410 Series Pressure Balacing Mixing Valves Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Zubehör fürs Wasser Powers 410 Series Pressure Balacing Mixing Valves herunter. Powers 410 Series Pressure Balacing Mixing Valves User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Zubehör fürs Wasser Powers 410 Series Pressure Balacing Mixing Valves